Hudson-robotics Bar Code Print and Apply Manuel d'utilisateur

Hudson Print and Apply USER MANUAL Rev 1.1 10 Stern Avenue, Springfield, NJ 07081 Tel: 973-376-7400  Fax: 973-376-8265

Print and Apply User Manual Hudson Robotics, Inc. 8 1. 1/8” Air Blast Tubing. (Color may vary.) 1

Print and Apply User Manual Hudson Robotics, Inc. 9 NOTE: DO NOT DISCARD the Hudson or Zebra Printer box. These cartons have been specially

Print and Apply User Manual Hudson Robotics, Inc. 10 B. Installing Media (Labels) After the PA1000 is setup correctly the media for the printer m

Print and Apply User Manual Hudson Robotics, Inc. 11 3. Once the media and print ribbon are installed, slide the edge of the media backing between

Print and Apply User Manual Hudson Robotics, Inc. 12 CHAPTER 3 - Calibration The Print and Apply is fully operational through SoftLinx V, with the

Print and Apply User Manual Hudson Robotics, Inc. 13 B. Setup Screen The unit requires setup in 3 steps to ensure successful use:  Label Ret

Print and Apply User Manual Hudson Robotics, Inc. 14 C. Hardware Setup Prior to Label Setup, the hardware must be configured to pick up labels pro

Print and Apply User Manual Hudson Robotics, Inc. 15 6. Press the (Next-Save) button until the tear off setting is displayed, using the (+) and (–

Print and Apply User Manual Hudson Robotics, Inc. 16 D. Label Setup To calibrate the unit for label retrieval, the user must obtain vacuum cutof

Print and Apply User Manual Hudson Robotics, Inc. 17 Once the head is over the label, press the “Save Point” button. It is highly recommended to

Print and Apply User Manual Hudson Robotics, Inc. i Table of Contents CHAPTER 1 - Overview ...

Print and Apply User Manual Hudson Robotics, Inc. 18 E. Apply Nest Setup To teach the unit how to apply a label to the selected nest, the user

Print and Apply User Manual Hudson Robotics, Inc. 19

Print and Apply User Manual Hudson Robotics, Inc. 20 CHAPTER 4 – Operation A. Creating Labels Codesoft v.9 is required to create labels. This se

Print and Apply User Manual Hudson Robotics, Inc. 21 To create a barcode, click on the barcode icon on the left toolbar (highlighted in the pictur

Print and Apply User Manual Hudson Robotics, Inc. 22 The barcode type, as well as attached counters can be modified on the screen below. Select a s

Print and Apply User Manual Hudson Robotics, Inc. 23 In addition, counter variables are used to automatically increment the barcode during operatio

Print and Apply User Manual Hudson Robotics, Inc. 24 B. Setup and Testing Apply Profiles Apply profiles tell the unit how to apply a label to

Print and Apply User Manual Hudson Robotics, Inc. 25

Print and Apply User Manual Hudson Robotics, Inc. 26 C. SoftLinx Operation The print and apply interface has two steps available in SoftLinx. The

Print and Apply User Manual Hudson Robotics, Inc. 27

Print and Apply User Manual Hudson Robotics, Inc. ii WARNING- -  This product may be used only in the manner described in this manual. When use

Print and Apply User Manual Hudson Robotics, Inc. 28 CHAPTER 5 - Maintenance A. Maintenance WARNING- -  Qualified personnel can perform all ma

Print and Apply User Manual Hudson Robotics, Inc. 29 CHAPTER 6 - Warranty & Service Agreement Terms and Conditions A. Warranty a. One-year co

Print and Apply User Manual Hudson Robotics, Inc. 30 B. Service Agreements I. Service Agreements, in one year periods, are available at preva

Print and Apply User Manual Hudson Robotics, Inc. 31 d. Warranty and service coverage does not include the following. Any service calls made as th

Print and Apply User Manual Hudson Robotics, Inc. 2 CHAPTER 1 - Overview The Print and Apply is an automated Barcode Labeling System. It creates

Print and Apply User Manual Hudson Robotics, Inc. 3 CHAPTER 2 – Installation A. Unpack the Print and Apply WARNING- -  Power switch must be tu

Print and Apply User Manual Hudson Robotics, Inc. 4 2. Open the Hudson box and remove the applicator from the box, also remove any additional comp

Print and Apply User Manual Hudson Robotics, Inc. 5 Figure 5 5. Attach all of the cables and accessories as shown in the following pictures, bef

Print and Apply User Manual Hudson Robotics, Inc. 6 1- Communication Cable to Rear of Printer 2- Optional Barcode Cable 3- Power Cable for

Print and Apply User Manual Hudson Robotics, Inc. 7 1- Air Pressure Regulator set to 60 PSI w/ ¼” Quick disconnect fitting. User supplies air in